眾做周知，清洗機的使用壽命長短與日常維護有很多的聯系，維護好了它的工作效率才能持續高效，而且使用的時間也會越來越長，下面我們來看下相關內容吧。

As we all know, the service life of the cleaning machine has a lot to do with daily maintenance. Only by maintaining its work efficiency can it continue to be efficient, and the use time will be longer and longer. Let's take a look at the related content.

工作效率比較高，相對于人工清潔來說，它可以快速的除塵除垢，還可以節省人工的勞動力。即使不用專用的清洗劑，它在清潔的時候加入適當?shù)南礈靹┮彩强梢赃_到很好的清潔效果。而且它的精度高，能夠清潔到很細微的縫隙和孔洞中，能滿足的特殊要求。

The work efficiency is relatively high. Compared with manual cleaning, it can quickly remove dust and dirt, and also save manual labor. Even without special detergent, it can achieve good cleaning effect by adding appropriate detergent when cleaning. Moreover, it has high precision and can be cleaned into very fine cracks and holes, which can meet the special requirements of professionals.

對于被清洗的物件不管是大的小的，簡單的還是復雜的，單量的還是批量的，清洗機都是可以獲得比較的清潔度。更重要的是通過清洗機清洗，更加節約水，噪音也比較小，而且設備的使用壽命很長，操作也比較簡單。

For the cleaned objects, whether large or small, simple or complex, single quantity or batch, the cleaning machine can obtain a relatively clean degree. What's more, cleaning with a cleaning machine saves more water, makes less noise, and has a long service life and simple operation.

通過日常的檢查，及時發現問題可以為設備的正常運轉打好“預防針”。一般日常維護有6項檢查：

Through daily inspection, finding problems in time can provide a "preventive injection" for the normal operation of the equipment. There are 6 inspections for general routine maintenance:

1、檢查清洗機的環境溫度和濕度是否符合標準。

1. Check whether the ambient temperature and humidity of the cleaning machine meet the standards.

2、檢查數顯溫控儀、電流表顯示的讀數是否正確。

2. Check whether the readings displayed by digital temperature controller and ammeter are correct.

3、檢查二極管和指示燈是否正常工作。

3. Check the diodes and indicators for proper operation.

4、檢查清洗機的管路出水口出水量情況。

4. Check the water output of the pipeline outlet of the washing machine.

5、檢查清洗機工作時振動、噪音是否異常。

5. Check whether the vibration and noise of the cleaning machine are abnormal during operation.

6、檢查超聲波清洗設備的表面是否有灰塵。

6. Check whether there is dust on the surface of ultrasonic cleaning equipment.

注意，清洗機在使用中也有可能發生常見問題。例如，在超聲波振子暴露在濕氣中的情況下，可以用兆歐表檢查與換能器連接的插頭，通過檢查絕緣電阻值可以判斷基本的狀況，一般要求絕緣電阻在5兆歐表以上。如果達不到該絕緣電阻值，通常換能器是濕的，所以可以將換能器整體放入烤箱，設定在溫度100度左右，干燥3小時，或者使用電吹風去除濕氣直到電阻值正常。

Note that common problems may also occur in the use of the cleaning machine. For example, when the ultrasonic vibrator is exposed to moisture, the plug connected to the transducer can be checked with a megger, and the basic condition can be judged by checking the insulation resistance value. Generally, the insulation resistance is required to be more than 5 megger. If the insulation resistance value cannot be reached, the transducer is usually wet, so you can put the transducer into the oven as a whole, set the temperature at about 100 ℃, and dry it for 3 hours, or use an electric hair dryer to remove the moisture until the resistance value is normal.

嚴禁在無清洗液的情況下接通電源，即清洗缸內未進入一定量的清洗液，不得關閉超聲波開關；有加熱設備的清洗設備在沒有液體時請勿打開加熱開關。更多注意事項就來關注網站www.phdgoplaces.com看信息吧。

It is strictly forbidden to turn on the power supply without cleaning fluid, that is, do not turn off the ultrasonic switch without a certain amount of cleaning fluid in the cleaning cylinder; Do not turn on the heating switch when there is no liquid in the cleaning equipment with heating equipment. For more notes, follow the website www.jnthcsb Read the information. Com.